Networking features of Distributed Cloud connected

This page describes the networking features of Google Distributed Cloud connected, including subnetworks, BGP peering sessions, and load balancing.

The procedures on this page only apply to Distributed Cloud connected racks, except load balancing, which applies to both Distributed Cloud connected racks and Distributed Cloud connected servers.

IPv4/IPv6 dual-stack networking

Distributed Cloud connected allows you to create clusters that use IPv4/IPv6 dual-stack networking. To take advantage of this functionality, you must order Distributed Cloud connected with dual-stack IPv4/IPv6 networking enabled. You cannot reconfigure and existing IPv4-only deployment of Distributed Cloud connected to IPv4/IPv6 dual-stack networking. To check whether your deployment supports IPv4/IPv6 dual-stack networking, follow the instructions in Get information about a machine and check the returned value of the dualstack_capable label.

In a dual-stack cluster, the IPv4 stack uses island mode, while the IPv6 stack uses flat mode. Because of this, you must specify individual, discrete node, and pod IPv6 addresses that belong to the same subnetwork. For more information, see Flat vs island mode network models.

For example, if your Distributed Cloud connected nodes and other local machines reside in the same Layer 2 domain, you could specify your IPv6 CIDR blocks for the cluster as follows:

Block purpose Block range Block size
IPv6 subnetwork fd12::/56 2^72
Pods fd12::1:0/59 2^69
Services fd12::2:0/59 2^69

This example assumes the following:

  • The node, pod, and service CIDR blocks belong to the fd:12::/56 supernetwork.
  • The node, pod, and service IP addresses are subnetworks of the specified CIDR block.
  • None of the subnetworks overlap.

IPv4/IPv6 dual-stack networking requires Layer 2 load balancing for IPv4 BGP peering and Layer 3 load balancing for IPv6 peering. For more information, see Load balancing.

For more information about deploying workloads on IPv4/IPv6 dual-stack clusters, see the following:

Enable the Distributed Cloud Edge Network API

Before you can configure networking on a connected deployment of Distributed Cloud, you must enable the Distributed Cloud Edge Network API. To do so, complete the steps in this section. By default, Distributed Cloud connected servers ship with the Distributed Cloud Edge Network API already enabled.

Console

  1. In the Google Cloud console, go to the Distributed Cloud Edge Network API page.

    Enable the API

  2. Click Enable.

gcloud

Use the following command:

gcloud services enable edgenetwork.googleapis.com

Configure networking on Distributed Cloud connected

This section describes how to configure the networking components on your Distributed Cloud connected deployment.

The following limitations apply to Distributed Cloud connected servers:

  • You can only configure subnetworks, and
  • Subnetworks only support VLAN IDs; CIDR-based subnetworks are not supported.

A typical network configuration for Distributed Cloud connected consists of the following steps:

  1. Optional: Initialize the network configuration of the target zone, if necessary.

  2. Create a network.

  3. Create one or more subnetworks within the network.

  4. Establish northbound BGP peering sessions with your PE routers by using the corresponding interconnect attachments.

  5. Establish southbound BGP peering sessions with the pods that run your workloads by using the corresponding subnetworks.

  6. Optional: Establish loopback BGP peering sessions for high availability.

  7. Test your configuration.

  8. Connect your pods to the network.

Optional: Initialize the network configuration of the Distributed Cloud zone

You must initialize the network configuration of your Distributed Cloud connected zone in the following cases:

  • Immediately after your Distributed Cloud connected hardware has been installed on your premises.
  • You upgraded to Distributed Cloud connected version 1.3.0 or later on an existing Distributed Cloud connected deployment but did not participate in the private preview of the Distributed Cloud Edge Network API.

Initializing the network configuration of a zone creates a default router named default and a default network named default. It also configures the default router to peer with all of the interconnects that you requested when you ordered the Distributed Cloud connected hardware by creating corresponding interconnect attachments. This configuration provides your Distributed Cloud connected deployment with basic uplink connectivity to your local network.

Initializing the network configuration of a zone is a one-time procedure. For complete instructions, see Initialize the network configuration of a zone.

Create a network

To create a new network, follow the instructions in Create a network. You must also create at least one subnetwork within the network to allow Distributed Cloud connected nodes to connect to the network.

Create one or more subnetworks

To create a subnetwork, follow the instructions in Create a subnetwork. You must create at least one subnetwork in your network to allow nodes to access the network. The VLAN corresponding to each subnetwork that you create is automatically available to all nodes in the zone.

For Distributed Cloud connected servers, you can only configure subnetworks using VLAN IDs. CIDR-based subnetworks are not supported.

Establish northbound BGP peering sessions

When you create a network and its corresponding subnetworks, they are local to their Distributed Cloud connected zone. To enable outbound connectivity, you must establish at least one northbound BGP peering session between the network and your peering edge routers.

To establish a northbound BGP peering session, do the following:

  1. List the interconnects available in your zone and then select the target interconnect for this peering session.

  2. Create one or more interconnect attachments on the selected interconnect. Interconnect attachments link the router that you create in the next step with the selected interconnect.

  3. Create a router. This router routes traffic between the interconnect and your network by using the interconnect attachments that you created in the previous step.

  4. Add an interface to the router for each interconnect attachment that you created earlier in this procedure. For each interface, use the IP address of the corresponding top-of-rack (ToR) switch in your Distributed Cloud connected rack. For instructions, see Establish a northbound peering session.

  5. Add a peer for each interface that you created on the router in the previous step.

Establish southbound BGP peering sessions

To enable inbound connectivity to your workloads from your local network, you must establish one or more southbound BGP peering sessions between your peering edge routers and the subnetwork to which your pods belong. The gateway IP address for each subnetwork is the IP address of the corresponding ToR switch in your Distributed Cloud connected rack.

To establish a southbound BGP peering session, do the following:

  1. Add an interface to the router in the target network for each subnetwork that you want to provision with inbound connectivity. For instructions, see Establish a southbound peering session.

  2. Add a peer for each interface that you created on the router in the previous step.

Optional: Establish loopback BGP peering sessions

To enable high-availability connectivity between your workloads and your local network, you can establish a loopback BGP peering session between the target pod and both ToR switches in your Distributed Cloud connected rack. A loopback peering session establishes two independent peering sessions for the pod, one with each ToR switch.

To establish a loopback BGP peering session, do the following:

  1. Add a loopback interface to the router in the target network. For instructions, see Establish a loopback peering session.

  2. Add a peer for the loopback interface.

Test your configuration

To test your configuration of the network components that you created, do the following:

  1. Check the operational status of the network.

  2. Check the provisioning status of each subnetwork.

  3. Check the operational status of the interconnects.

  4. Check the operational status of the interconnect attachments.

  5. Check the operational status of the router.

Connect your pods to the network

To connect your pods to the network and configure advanced network functions, follow the instructions in Network Function operator.

Load balancing

Distributed Cloud connected ships with the following load balancing solutions:

  • Layer 2 load balancing with MetalLB
  • Layer 3 load balancing with Google Distributed Cloud load balancers

The load balancing solutions built into Distributed Cloud connected cannot use overlapping Kubernetes service virtual IP prefixes. If you have an existing Distributed Cloud connected deployment that uses Layer 2 MetalLB load balancing, and you want to switch to Layer 3 load balancing with Google Distributed Cloud load balancers, you must use a service virtual IP prefix that does not overlap with the prefix used by your Layer 2 MetalLB load balancing configuration.

Layer 2 load balancing with MetalLB

Distributed Cloud ships with a bundled network load balancing solution based on MetalLB in Layer 2 mode. You can use this solution to expose services that run in your Distributed Cloud zone to the outside world by using virtual IP addresses (VIPs) as follows:

  1. Your network administrator plans the network topology and specifies the required virtual IPv4 address subnetwork when ordering Distributed Cloud. Google configures your Distributed Cloud hardware accordingly before delivery. Keep the following in mind:
    • This VIP subnetwork is shared among all Kubernetes clusters that run within your Distributed Cloud zone.
    • A route for the requested VIP subnetwork is advertised through the BGP sessions between the Distributed Cloud zone and your local network.
    • The first (network ID), second (default gateway), and last (broadcast address) addresses in the subnetwork are reserved for core system functionality. Do not assign those addresses to your MetalLB configurations' address pools.
    • Each cluster must use a separate VIP range that falls within the configured VIP subnetwork.
  2. When you create a cluster in your Distributed Cloud zone, your cluster administrator specifies the pod and ClusterIP service address pools by using CIDR notation. Your network administrator provides the appropriate LoadBalancer VIP subnetwork to your cluster administrator.
  3. After the cluster is created, the cluster administrator configures the corresponding VIP pools. You must specify the VIP pools by using the --external-lb-ipv4-address-pools flag when you create the cluster. For more information, see Survivability mode.

  4. The cluster administrator creates the appropriate Kubernetes LoadBalancer services.

Distributed Cloud nodes in a single node pool share a common Layer 2 domain and are therefore also MetalLB load balancer nodes.

Layer 3 load balancing with Google Distributed Cloud load balancers

Distributed Cloud connected ships with a bundled network load balancing solution based on the Google Distributed Cloud bundled load balancers in Layer 3 mode configured as BGP speakers. You can use this solution to expose services that run in your Distributed Cloud connected zone to the outside world by using VIPs.

You can specify the VIP ranges for the corresponding LoadBalancer services by using the metallb-config ConfigMap. For example:

kind: ConfigMap
apiVersion: v1
data:
  config: |
    address-pools:
    - name: default
      protocol: bgp
      addresses:
      - 10.100.10.66/27
metadata:
  name: metallb-config
  namespace: metallb-system

In the preceding example, each LoadBalancer service that you configure is automatically assigned a virtual IP address from the 10.100.10.66/27 range specified in the ConfigMap. These VIPs are then advertised northbound by the Distributed Cloud BGP speakers configured on the ToR switches through the BGPPeer resources.

When you create a Distributed Cloud cluster, the following resources are automatically created on that cluster:

  • A BGPLoadBalancer resource that instantiates the BGP load balancer.
  • A NetworkGatewayGroup resource that specifies the local floating IP addresses to use for the BGP speakers. These IP addresses are automatically set to the last two IP addresses of the Kubernetes node subnetwork assigned to the cluster.

With those resources in place, you can set up BGP sessions to the Distributed Cloud ToR switches by configuring corresponding BGPPeer resources. To do so, you must have the necessary autonomous system numbers (ASNs) and the loopback peer IP addresses for the ToR switches. These IP addresses serve as the ToR switch BGP session endpoints on the default network resource. Keep in mind that the value of the network parameter must be pod-network.

Following is an example of the two BGPPeer resources:

kind: BGPPeer
apiVersion: networking.gke.io/v1
metadata:
  name: bgppeertor1
  labels:
    cluster.baremetal.gke.io/default-peer: "true"
  namespace: kube-system
spec:
  network: pod-network
  localASN: 64777
  peerASN: 64956
  peerIP: 10.112.0.10
  sessions: 1
kind: BGPPeer
apiVersion: networking.gke.io/v1
metadata:
  name: bgppeertor2
  labels:
    cluster.baremetal.gke.io/default-peer: "true"
  namespace: kube-system
spec:
  network: pod-network
  localASN: 64777
  peerASN: 64956
  peerIP: 10.112.0.11
  sessions: 1

Configure Layer 3 BGP load balancing automation for IPv6 peering

Before you can begin using IPv6 peering on your IPv4/IPv6 dual-stack networking cluster, you must work with Google Support to enable Google Distributed Cloud load balancer automation on your Distributed Cloud connected deployment.

Create Layer 3 LoadBalancer service

After you have enabled enable Google Distributed Cloud load balancer automation on your Distributed Cloud connected deployment, instantiate the Layer 3 LoadBalancer service. For example:

apiVersion: v1
kind: Service
metadata:
  name: my-service
  labels:
    app.kubernetes.io/name: MyApp
spec:
  ipFamilyPolicy: PreferDualStack
  ipFamilies:
  - IPv6
  - IPv4
  selector:
    app.kubernetes.io/name: MyApp
  type: LoadBalancer
  ports:
    - protocol: TCP
      port: 80

Check the state of the BGP session and load balancing services

To check the state of your BGP session, use the following command:

kubectl get bgpsessions.networking.gke.io -A

The command returns output similar to the following example:

NAMESPACE     NAME                                                 LOCAL ASN   PEER ASN   LOCAL IP        PEER IP         STATE            LAST REPORT
kube-system   bgppeertor1-np-den6-120demo-den6-04-6ad5b6f4         64777       64956      10.100.10.61    10.112.0.10     Established      2s
kube-system   bgppeertor2-np-den6-120demo-den6-04-6ad5b6f4         64777       64956      10.100.10.61    10.112.0.11     Established      2s

To verify that your LoadBalancer services are being advertised by the BGP speakers, use the following command:

kubectl get bgpadvertisedroutes.networking.gke.io -A

The command returns output similar to the following example:

NAMESPACE      NAME                           PREFIX            METRIC
kube-system    bgplb-default-service-tcp      10.100.10.68/32
kube-system    bgplb-default-service-udp      10.100.10.77/32

Distributed Cloud ingress

In addition to load balancing, Distributed Cloud connected also supports Kubernetes Ingress resources. A Kubernetes Ingress resource controls the flow of HTTP(S) traffic to Kubernetes services that run on your Distributed Cloud connected clusters. The following example illustrates a typical Ingress resource:

apiVersion: networking.k8s.io/v1
kind: Ingress
metadata:
  name: my-ingress
spec:
  rules:
  - http:
      paths:
      - backend:
          service:
            name: my-service
            port:
              number: 80
        path: /foo
        pathType: Prefix

When configured, network traffic flows through the istio-ingress service, which by default is assigned a random IP address from the VIP pools specified in your MetalLB configuration. You can select a specific IP address or a virtual IP address from the MetalLB configuration by using the loadBalancerIP field in the istio-ingress service definition. For example:

apiVersion: v1
kind: service
metadata:
  labels:
    istio: ingress-gke-system
    release: istio
  name: istio-ingress
  namespace: gke-system
spec:
  loadBalancerIP: <targetLoadBalancerIPaddress>

This functionality is not available on Distributed Cloud connected servers.

Disable the default Distributed Cloud Ingress resource

By default, when you create a Distributed Cloud connected cluster, Distributed Cloud automatically configures the istio-ingress service for the cluster. You have the option to create a Distributed Cloud connected cluster without the istio-ingress service. To do so, complete the following steps:

gcloud

  1. Create a YAML configuration file named SystemsAddonConfig.yaml with the following contents:

    systemAddonsConfig:
     ingress:
       disabled: true
    
  2. Pass the SystemsAddonConfig.yaml file by using the --system-addons-config flag in your cluster creation command. You must use the gcloud alpha version to use this feature. For example:

    gcloud alpha edge-cloud container clusters create MyGDCECluster1 --location us-west1 \
        --system-addons-config=SystemsAddonConfig.yaml
    

    For more information about creating a Distributed Cloud cluster, see Create a cluster.

API

  1. Add the following JSON content to the JSON payload in your cluster creation request:

    "systemAddonConfig" {
       "ingress" {
               "disabled": true
       }
    }
    
  2. Submit the cluster creation request as described in Create a cluster.

NodePort service

Distributed Cloud connected supports the Kubernetes NodePort service that listens for connections on a Distributed Cloud node at a port number of your choice. The NodePort service supports the TCP, UDP, and SCTP protocols. For example:

apiVersion: v1
kind: pod
metadata:
  name: socat-nodeport-sctp
  labels:
    app.kubernetes.io/name: socat-nodeport-sctp
spec:
  containers:
  - name: socat-nodeport-sctp
    ...
    ports:
      - containerPort: 31333
        protocol: SCTP
        name: server-sctp

---

apiVersion: v1
kind: service
metadata:
  name: socat-nodeport-sctp-svc
spec:
  type: NodePort
  selector:
    app.kubernetes.io/name: socat-nodeport-sctp
  ports:
    - port: 31333
      protocol: SCTP
      targetPort: server-sctp
      nodePort: 31333

SCTP support

Distributed Cloud connected supports the Stream Control Transmission Protocol (SCTP) on the primary network interface for both internal and external networking. SCTP support includes the NodePort, LoadBalancer, and ClusterIP service types. pods can use SCTP to communicate with other pods and external resources. The following example illustrates how to configure IPERF as a ClusterIP service by using SCTP:

apiVersion: v1
kind: pod
metadata:
  name: iperf3-sctp-server-client
  labels:
    app.kubernetes.io/name: iperf3-sctp-server-client
spec:
  containers:
  - name: iperf3-sctp-server
    args: ['-s', '-p 31390']
    ports:
      - containerPort: 31390
        protocol: SCTP
        name: server-sctp
  - name: iperf3-sctp-client
    ...

---

apiVersion: v1
kind: service
metadata:
  name: iperf3-sctp-svc
spec:
  selector:
    app.kubernetes.io/name: iperf3-sctp-server-client
  ports:
    - port: 31390
      protocol: SCTP
      targetPort: server-sctp

This functionality is not available on Distributed Cloud connected servers.

SCTP kernel modules

Starting with version 1.5.0, Distributed Cloud connected configures the sctp Edge OS kernel module as loadable. This allows you to load your own SCTP protocol stacks in the kernel user space.

Additionally, Distributed Cloud connected loads the following modules into the kernel by default:

Module name Config name
fou CONFIG_NET_FOU
nf_conntrack_proto_gre CONFIG_NF_CT_PROTO_GRE
nf_conntrack_proto_sctp CONFIG_NF_CT_PROTO_SCTP
inotify CONFIG_INOTIFY_USER
xt_redirect CONFIG_NETFILTER_XT_TARGET_REDIRECT
xt_u32 CONFIG_NETFILTER_XT_MATCH_U32
xt_multiport CONFIG_NETFILTER_XT_MATCH_MULTIPORT
xt_statistic CONFIG_NETFILTER_XT_MATCH_STATISTIC
xt_owner CONFIG_NETFILTER_XT_MATCH_OWNER
xt_conntrack CONFIG_NETFILTER_XT_MATCH_CONNTRACK
xt_mark CONFIG_NETFILTER_XT_MARK
ip6table_mangle CONFIG_IP6_NF_MANGLE
ip6_tables CONFIG_IP6_NF_IPTABLES
ip6table_filter CONFIG_IP6_NF_FILTER
ip6t_reject CONFIG_IP6_NF_TARGET_REJECT
iptable_mangle CONFIG_IP_NF_MANGLE
ip_tables CONFIG_IP_NF_IPTABLES
iptable_filter CONFIG_IP_NF_FILTER

ClusterDNS resource

Distributed Cloud connected supports the Google Distributed Cloud ClusterDNS resource for configuring upstream name servers for specific domains by using the spec.domains section. For more information about configuring this resource, see spec.domains.

This functionality is not available on Distributed Cloud connected servers.

What's next