Configure Network Connectivity Gateway

Preview

This product or feature is subject to the "Pre-GA Offerings Terms" in the General Service Terms section of the Service Specific Terms. Pre-GA products and features are available "as is" and might have limited support. For more information, see the launch stage descriptions.

This document shows how to configure Network Connectivity Gateway for a cluster in Google Distributed Cloud.

Sometimes you have Pods running in a cluster that must communicate with workloads running in a Virtual Private Cloud (VPC). This communication must be secure. And perhaps you need this communication to occur over a flat network without using a proxy server. Network Connectivity Gateway enables this kind of communication.

Network Connectivity Gateway runs as a Pod in your cluster. As shown in the following diagram, this solution provides IPsec tunnels for traffic from Pods in your cluster to VMs in a VPC. When the gateway Pod receives prefixes for VPC subnets over a Border Gateway Protocol (BGP) session, it sets up forwarding by using Dataplane V2. When other Pods send traffic to an address with one of those prefixes, the traffic is steered to the gateway Pod. Then the gateway Pod routes the traffic over an IPsec tunnel toward Google Cloud.

Note: Google Distributed Cloud running on Ubuntu 18.04 isn't supported for Network Connectivity Gateway, but all other OSes supported by Google Distributed Cloud are supported. For the list of the Linux distributions and versions that are supported by Google Distributed Cloud, see Select your operating system.

Network Connectivity Gateway doesn't support the following features and capabilities:

• IPv6 for HA VPN (and BGP)
• MD5 for BGP
• Bidirectional Forwarding Detection (BFD) for BGP

Create Google Cloud resources

Before you enable Network Connectivity Gateway in a cluster, you must have the following Google Cloud resources:

• A Cloud Router

• An HA VPN gateway

• A peer VPN gateway: one interface

• Two VPN tunnels

• Two BGP sessions: one for each of your VPN tunnels

For information on how to create and configure these resources, see Creating an HA VPN gateway to a peer VPN gateway.

As you create these resources, gather the following information, and have it available for later:

• The two external IP addresses that Google Cloud assigned to your HA VPN gateway.

• The public IP address for IPsec/VPN traffic that leaves your organization. This address might be the result of a network address translation (NAT).

• Your pre-shared key.

• The autonomous system number (ASN) that you assigned to your Cloud Router for BGP sessions.

• The ASN you've chosen to use in your on-premises cluster for BGP sessions.

• For each BGP session, the link-local address, such as 169.254.1.1, to be used by your Cloud Router and the link-local address to be used in your on-premises cluster.

For information on how to find the details for your BGP session configuration, see View BGP session configuration.

Cluster requirements

The Network Connectivity Gateway command-line tool download, ncgctl-v1.12.0-linux-amd64.tar.gz is compatible with version 1.12 of Google Distributed Cloud only. If you are creating a new version 1.12.0 cluster, you enable Network Connectivity Gateway with an annotation in the cluster configuration file.

Note: If you have an existing version 1.12.0 or higher cluster, you can use an ncgctl command to enable Network Connectivity Gateway. For more information, see Install.

To enable Network Connectivity Gateway during cluster creation:

1. In the cluster configuration file, add the baremetal.cluster.gke.io/enable-gng: "true" annotation.

   apiVersion: baremetal.cluster.gke.io/v1
   kind: Cluster
   metadata:
     annotations:
       baremetal.cluster.gke.io/enable-gng: "true"
     name: my-cluster
     namespace: cluster-my-cluster
   spec:
   ...
     anthosBareMetalVersion: 1.12.0
     ...
   

2. Use bmctl create to create the cluster:

   bmctl create cluster -c CLUSTER_NAME
   

   Replace CLUSTER_NAME with the name you that specified when you created the cluster configuration file. For more information about creating clusters, see Cluster creation overview.

Download

To download ncgctl, the Network Connectivity Gateway command-line tool, follow these steps:

1. Download the Network Connectivity Gateway components and custom resource definitions:

   gcloud storage cp gs://ncg-release/anthos-baremetal/ncgctl-v1.12.0-linux-amd64.tar.gz .
   

2. Extract the archive:

   tar -xvzf ncgctl-v1.12.0-linux-amd64.tar.gz
   

Install

To install ncgctl, follow these steps:

1. Run preflight checks to make sure the cluster satisfies the prerequisites. For example, make sure that Dataplane V2 is enabled.

   ./bin/ncgctl --verify --kubeconfig CLUSTER_KUBECONFIG
   

   Replace CLUSTER_KUBECONFIG with the path of your cluster kubeconfig file.

2. Install Network Connectivity Gateway.

   ./bin/ncgctl --install --kubeconfig CLUSTER_KUBECONFIG
   

   Note: If you are creating a new version 1.12.0 cluster, you can skip the following steps. When you create clusters, we recommend that you add the baremetal.cluster.gke.io/enable-gng: "true" annotation to your cluster configuration file to enable Network Connectivity Gateway}. For more information, see Cluster requirements.

3. If you have an existing version 1.12.0 cluster, you can use the following ncgctl command to enable Network Connectivity Gateway:

   ./bin/ncgctl --enable-ncg-on-existing-cluster
   

   The ncgctl command accepts -e as a shortened version of the enable flag.

4. To see additional shortcuts and other command help, use the following command:

   ./bin/ncgctl --help
   

Create a Secret for your pre-shared key

The gateways at either end of the IPsec tunnels use a Secret containing your pre-shared key for authentication.

To create the Secret, follow these steps:

1. Create a file named psk-secret.yaml with the following Secret manifest details:

   apiVersion: v1
   kind: Secret
   metadata:
     name: "ike-key"
     namespace: "kube-system"
   data:
     psk: PRE_SHARED_KEY
   

   Replace PRE_SHARED_KEY with a base64-encoded pre-shared key. If you have a key in plaintext, encode the key to base64 format before you create this Secret. For example, if the Google Cloud console generated a key for you, it is in plaintext, and you must encode it. To base64 encode a key:

   echo -n PLAINTEXT_KEY | base64
   

2. Create the Secret:

   kubectl --kubeconfig CLUSTER_KUBECONFIG apply -f psk-secret.yaml
   

Create two OverlayVPNTunnel custom resources

To start two IPsec sessions, create two OverlayVPNTunnel custom resources.

1. Create a file named overlay-vpn-tunnels.yaml with the following OverlayVPNTunnel manifest details:

   apiVersion: networking.gke.io/v1alpha1
   kind: OverlayVPNTunnel
   metadata:
     namespace: "kube-system"
     name: TUNNEL_1_NAME
   spec:
     ikeKey:
       name: "ike-key"
       namespace: "kube-system"
     peer:
       publicIP: PEER_PUBLIC_IP_1
     self:
       publicIP: SELF_PUBLIC_IP
     localTunnelIP: SELF_LOCAL_TUNNEL_IP_1
   ---
   apiVersion: networking.gke.io/v1alpha1
   kind: OverlayVPNTunnel
   metadata:
     namespace: "kube-system"
     name: TUNNEL_2_NAME
   spec:
     ikeKey:
       name: "ike-key"
       namespace: "kube-system"
     peer:
       publicIP: PEER_PUBLIC_IP_2
     self:
       publicIP: SELF_PUBLIC_IP
     localTunnelIP: SELF_LOCAL_TUNNEL_IP_2
   

   Replace the following:

   • TUNNEL_NAME_1: a name of your choice for the first OverlayVPNTunnel.

   • TUNNEL_NAME_2: a name of your choice for the second OverlayVPNTunnel.

   • PEER_PUBLIC_IP_1: the public IP address of one interface on your HA VPN gateway. You specified this interface when you created your first VPN tunnel.

   • PEER_PUBLIC_IP_2: the public IP address of the other interface on your HA VPN gateway. You specified this interface when you created your second VPN tunnel.

   • SELF_LOCAL_TUNNEL_IP_1: the link-local address to be used in your cluster for BGP sessions over the first tunnel.

   • SELF_LOCAL_TUNNEL_IP_2: the link-local address to be used in your cluster for BGP sessions over the second tunnel.

   • SELF_PUBLIC_IP: the public IP address for IPsec/VPN traffic that leaves your organization. This address might be the result of a network address translation (NAT).

2. Create the two OverlayVPNTunnels:

   kubectl --kubeconfig CLUSTER_KUBECONFIG apply -f overlay-vpn-tunnels.yaml
   

3. Check the status of the tunnels:

   kubectl --kubeconfig CLUSTER_KUBECONFIG get OverlayVPNTunnel \
       --namespace kube-system --output yaml
   

Create two OverlayBGPPeer custom resources

To start a BGP session over each of the tunnels, create two OverlayBGPPeer custom resources.

1. Create a file named overlay-bgp-peers.yaml with the following OverlayBGPPeer manifest details.

   apiVersion: networking.gke.io/v1alpha1
   kind: OverlayBGPPeer
   metadata:
     namespace: "kube-system"
     name: BGP_PEER_1_NAME
   spec:
     localASN: LOCAL_ASN
     localIP: LOCAL_IP
     peerIP: PEER_IP_1
     peerASN: PEER_ASN
     vpnTunnel: TUNNEL_1_NAME
   ---
   apiVersion: networking.gke.io/v1alpha1
   kind: OverlayBGPPeer
   metadata:
     namespace: "kube-system"
     name: BGP_PEER_2_NAME
   spec:
     localASN: LOCAL_ASN
     localIP: LOCAL_IP
     peerIP: PEER_IP_2
     peerASN: PEER_ASN
     vpnTunnel: TUNNEL_2_NAME
   

   Replace the following:

   • BGP_PEER_1_NAME: a name of your choice for the first OverlayBGPPeer.

   • BGP_PEER_2_NAME: a name of your choice for the second OverlayBGPPeer.

   • LOCAL_ASN: the ASN to be used in your cluster for BGP sessions.

   • LOCAL_IP: the public IP address for IPsec/VPN traffic that leaves your organization. This address might be the result of a network address translation (NAT).

   • PEER_IP_1: the public IP address of one interface on your HA VPN gateway. You specified this interface when you created your first VPN tunnel.

   • PEER_IP_2: the public IP address of the other interface on your HA VPN gateway. You specified this interface when you created your second VPN tunnel.

   • PEER_ASN: the ASN assigned to your Cloud Router for BGP sessions.

   • TUNNEL_1_NAME: the name of the first OverlayVPNTunnel that you created previously.

   • TUNNEL_2_NAME: the name of the second OverlayVPNTunnel that you created previously.

2. Create the OverlayBGPPeer custom resources:

   kubectl --kubeconfig CLUSTER_KUBECONFIG apply -f overlay-bgp-peers.yaml
   

3. Check the status of the BGP sessions:

   kubectl --kubeconfig CLUSTER_KUBECONFIG get OverlayBGPPeer --namespace kube-system \
       --output yaml
   

Check the status of Network Connectivity Gateway

The installation created a NetworkConnectivityGateway custom resource.

• View the NetworkConnectivityGateway custom resource:

  kubectl --kubeconfig CLUSTER_KUBECONFIG get NetworkConnectivityGateway --namespace kube-system \
      --output yaml
  

  The output is similar to the following. Verify that you see Status: Healthy:

  apiVersion: networking.gke.io/v1alpha1
  kind: NetworkConnectivityGateway
  metadata:
    namespace: kube-system
    name: default
  spec:
  status:
      CurrNode: worker1-node
      CreatedTime: 2021-09-07T03:18:15Z
      LastReportTime: 2021-09-21T23:57:54Z
      Status:  Healthy
  

Check the Network Connectivity Gateway logs

The gateway Pod belongs to a DaemonSet named ncgd, so the Pod name begins with ncgd.

To view the Network Connectivity Gateway logs, follow these steps:

1. Find the name of the gateway Pod:

   kubectl --kubeconfig CLUSTER_KUBECONFIG pods --namespace kube-system | grep ncgd
   

2. View the logs from the gateway Pod:

   kubectl --kubeconfig CLUSTER_KUBECONFIG logs GATEWAY_POD --namespace kube-system \
       --output yaml
   

   Replace GATEWAY_POD with the name of the gateway Pod.

Uninstall

To uninstall Network Connectivity Gateway from a cluster:

./bin/ncgctl –-uninstall --kubeconfig CLUSTER_KUBECONFIG

Troubleshooting

For troubleshooting tips related to Network Connectivity Gateway, see Troubleshooting Network Connectivity Gateway.